收藏本站
Atmel LED Drivers-MSL2160/MSL2161
16-string, White and RGB LED Drivers with Adaptive Configuration,
EEPROM, and SPI/I 2 C/SMBus Serial Interface
Connecting the Efficiency Optimizer to an LED String Power Supply and Selecting Resistors
The MSL2160/1 are designed to control external LED string power supplies that use voltage dividers (R TOP and R BOTTOM
in Figure 5) to set the output voltage, and whose regulation feedback voltage is not more than 3.5V. The Efficiency
Optimizer improves power efficiency by injecting a current of between 0 and 255μA into the voltage dividers of the
external power supplies, dynamically adjusting their outputs to the minimum voltage required by the LED strings. To
select the resistors, first determine V OUT(MIN) and V OUT(MAX) , the minimum and maximum string supply voltage limits, using:
V OUT ( MIN ) = ( V f ( MIN ) ? [ # ofLEDs ] ) + 0 . 5
and
V OUT ( MAX ) = ( V f ( MAX ) ? [ # ofLEDs ] ) + 0 . 5 ,
where V f(MIN) and V f(MAX) are the LED minimum and maximum forward voltage drops at the peak current set by R S (page
12). For example, if the LED data are V f(MIN) = 3.5V and V f(MAX) = 3.8V, and ten LEDs are used in a string, then the total
minimum and maximum voltage drops across a string are 35V and 38V, respectively. Adding an allowance of 0.5V for the
string drive MOSFET headroom brings V OUT(MIN) to 35.5V and V OUT(MAX) to 38.5V. Then, determine R TOP using:
R TOP =
V OUT ( MAX ) ? V OUT ( MIN )
I FBOn ( MAX )
,
where I FBOn(MAX) is the 255μ A maximum output current of the efficiency optimizer outputs FBOn. Finally, determine R BOTTOM using:
R BOTTOM = R TOP ?
V FB
V OUT ( MAX ) ? V FB ,
where V FB is the regulation feedback voltage of the power supply. Place a diode (1N4148 or similar) between FBOn and
the supply’s feedback node to protect the MSL2160/1 against current flow into FBOn. Assign all strings powered by a
common supply to the proper FBO output using string set registers 0x40 - 0x5F.
Once configured, determine the change in power supply output voltage in response to a change in FBO output current using:
? V OUT = ? I FBO ? R TOP .
Direct PWM Control of the LED Strings
An external PWM signal applied to the PWM input allows direct PWM control over the strings when bits PWMEN and
PWMDIRECT (bits D0 and D1 in PWM control register 0x2D) are set to 1. This configuration bypasses PHI and GSC, but
allows LED string phase delay via the phase delay enable bit, PHADLYEN (bit D0 of register 0x2E). With phase delay
enabled, a progressive delay of 1/16 the PWM frame is calculated and applied successively to each string drive signal.
The PWM input can also be configured as a gate for the output of the PWM engine using PWM global enable
(bit D2 of the PWM control register 0x2D).
Atmel LED Drivers-MSL2160/MSL2161
21
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MSL2162DQ IC LED DRIVER 16 STRING
MSL3082CS IC LED DRIVER 8 STRING
MSL3085BT IC LED DRIVER 8 STRING
MSL3162BT IC LED DRIVER 16 STRING
MSL3164BT IC LED DRIVER 16 STRING
MSL3167GU IC LED DRIVER 16 STRING
MT-6 PLUS SURGE SUPPR TCHMSTR 6OUT 10'CORD
MT42L256M32D4KP-3 IT:A IC LPDDR2 SDRAM 8GBIT 168FBGA
相关代理商/技术参数
MSL2160DQ-R 功能描述:LED照明驱动器 16String White & RGB LED Drivers with A RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MSL2161 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:16-string, White and RGB LED Drivers with Adaptive Configuration, EEPROM, and SPI/I2C/SMBus Serial Interface
MSL2161DQ 功能描述:LED照明驱动器 16String White & RGB LED Drivers with A RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MSL2161DQ-R 功能描述:LED照明驱动器 16String White & RGB LED Drivers with A RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MSL2162DQ 功能描述:LED照明驱动器 16-String RGBWhite LED Dvrs AdapCon E2P RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MSL2162DQ-R 功能描述:LED照明驱动器 16String White & RGB LED Driver with Ad RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MSL2164-DU 功能描述:LED照明驱动器 16-String LED Driver Mult-PWM Modes 3FO RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MSL2164-DUR 功能描述:LED照明驱动器 16-String LED Driver Mult-PWM Modes 3FO RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N